Hammer Miner Thor P2 10 TH/s Home Bitcoin Miner

The Thor P2 fills the gap between small single-chip desktop miners and loud, high-current industrial ASICs. It puts up to 10 TH/s of real Bitcoin hashrate on a desk or shelf while staying on a standard household outlet and drawing no more than approximately 157W in its published Overclock profile.

Unlike a bare board that still needs a power supply, cooler, fan, stand, and wiring, the Thor P2 arrives assembled, tested, and firmware-flashed. Its 240W power adapter, 120mm tower cooler, eight copper heatpipes, ARGB fan, ABS stand, color display, and network hardware are already part of the package.

Use the purchase controls above to order the Hammer Miner Thor P2 from CryptoCloaks.

Want the deeper analysis first? Read our 3,400-word Hammer Miner Thor P2 research review for source-by-source wall-power ranges, independent video observations, Thor OS firmware history, electricity costs, setup checks, and comparisons with four other home Bitcoin miners.

Why choose the Thor P2?

• Up to 10 TH/s: dual BM1373 SHA-256 mining performance in a home-friendly format.
• Three tested modes: move between lower power, balanced operation, and maximum hashrate.
• Measured wall-power figures: compare electricity use using approximately 60W, 88W, and 157W rather than firmware estimates alone.
• Serious cooling: a 120mm tower heatsink, eight copper heatpipes, and 120mm fan provide thermal headroom.
• WiFi plus Ethernet: use easy wireless setup or a stable wired connection for 24/7 mining.
• Local display and dashboard: check hashrate, pools, settings, block data, and Bitcoin price information.
• 240W PSU included: the 12V/20A adapter leaves headroom above the published 157W maximum mode.
• Pool or solo-pool: choose steadier pool payouts or probabilistic solo mining.
• ARGB lighting: select color cycle, marquee, breathing, flashing, or turn the lighting off.
• Compact footprint: approximately 5.99 x 5.7 x 6.94 inches and 1 lb 13 oz.

Thor P2 hashrate, power, efficiency, and noise

These published mode figures are tested starting points, not guaranteed output. Actual results vary with firmware, tuning, ambient temperature, airflow, power quality, network conditions, and individual hardware. The detailed source table reports power measured at the wall.

Start with a tested mode and verify stable temperature, accepted shares, fan behavior, and network uptime before changing frequency or voltage. Higher hashrate settings create more heat and may reduce efficiency.

Eight-heatpipe cooling built for sustained mining

Two BM1373 chips need more cooling than a typical single-chip desktop board. The Thor P2 uses a 120mm tower cooler with eight copper heatpipes and a full-size ARGB fan. The larger surface area lets the fan move heat without using the high-speed blower system found in industrial miners.

Keep the fan intake and exhaust open. Do not place the miner in a sealed cabinet, against a wall that blocks airflow, or in a wet, dusty, or excessively humid area. Published ambient operating range is 0 to 45 degrees Celsius.

WiFi, Ethernet, color display, and local controls

The LilyGO T-Display S3 controller combines an ESP32-S3 with a color LCD. The interface can show live hashrate, mining status, pool configuration, device settings, block monitoring, and Bitcoin price information. The local dashboard provides a larger view for performance and configuration.

WiFi keeps first-time placement flexible. Ethernet is the better choice when the miner can reach a cable because it removes wireless interference and signal quality from the mining path.

What’s included

• Hammer Miner Thor P2 dual-BM1373 Bitcoin miner
• 3D-printed ABS desktop stand
• 12V/20A 240W AC power adapter with XT60 connector
• US AC power cable
• EU AC power cable

You still need: a wall outlet, WiFi or Ethernet network connection, a compatible Bitcoin pool or solo-pool endpoint, and payout information required by your chosen service. An Ethernet cable is not listed as included.

Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases.

Thor P2 specifications

Thor P2 vs CryptoCloaks home Bitcoin miners

The Thor P2 is the middle step for buyers who want substantially more hashrate than a single-chip miner while staying well below industrial power and noise.

Compare CryptoCloaks home Bitcoin miners by hashrate, power, noise, and connectivity.

Pool mining vs solo mining

Pool mining combines your hashrate with other miners and pays according to the pool’s rules and your contributed work. It is the practical choice for smaller, more frequent payouts, but results still depend on pool terms, fees, uptime, Bitcoin price, network difficulty, and electricity cost.

Solo-pool mining gives the full block reward to the winning miner after any service terms, but the odds of finding a block at 10 TH/s remain extremely long and no result is guaranteed. Solo mining is best treated as a Bitcoin hobby, network participation, and probabilistic experiment rather than predictable income.

Hammer Miner Thor P2 setup

1. Place the assembled miner on a flat, stable surface with clear air around the 120mm fan and heatsink.
2. Connect the included XT60 power adapter to the miner, then connect the correct AC cable to a 100-240V outlet.
3. For wired networking, connect an Ethernet cable. For WiFi, connect a phone or computer to the temporary setup network shown by the miner.
4. Open 192.168.4.1 while connected to the setup network, enter the 2.4GHz WiFi name and password, save, and restart.
5. Open the miner’s local interface after it joins your network.
6. Enter the pool URL, worker name, and payout details required by your pool or solo-pool service.
7. Start in Low Power or Normal mode and verify temperature, hashrate, accepted shares, fan speed, and network stability.
8. Use Overclock mode only with unrestricted airflow and active temperature monitoring.

Heat, noise, and honest operating expectations

Nearly all electrical power used by a Bitcoin miner becomes room heat. The Thor P2 adds approximately 60W of heat in Low Power mode, 88W in Normal mode, or 157W in Overclock mode. That is far below a typical industrial ASIC, but it is still noticeable in a small closed room over time.

Published sound figures range from approximately 35 to 44 dB. Distance, fan condition, ambient temperature, nearby walls, desk vibration, and room acoustics affect what you hear. Treat the ratings as comparison points, not promises for every room.

Hammer Miner Thor P2 FAQ

How much hashrate does the Thor P2 produce?

Published targets are approximately 4.8 TH/s in Low Power mode, 6.8 TH/s in Normal mode, and 10 TH/s in Overclock mode. Actual results vary with tuning and operating conditions.

How much power does the Thor P2 use?

The detailed measured-at-the-wall mode table lists approximately 60W, 88W, and 157W. The package includes a 240W power supply with headroom above the published maximum mode.

How efficient is the Thor P2?

Published efficiencies are approximately 12.5 J/TH in Low Power mode, 12.9 J/TH in Normal mode, and 15.7 J/TH in Overclock mode.

How loud is the Hammer Miner Thor P2?

Published figures are approximately 35 dB on Low Power, 41 dB on Normal, and 44 dB on Overclock. Room acoustics, distance, fan speed, and ambient temperature affect perceived noise.

Does the Thor P2 include a power supply?

Yes. It includes a 12V/20A 240W adapter with XT60 connector plus US and EU AC power cables.

Does the Thor P2 support Ethernet?

Yes. The Thor P2 supports both 2.4GHz WiFi and Ethernet. An Ethernet cable is not listed as included.

What ASIC chips are in the Thor P2?

It uses two Bitmain BM1373 SHA-256 ASIC chips from Bitmain’s 3nm generation.

Can the Thor P2 mine Bitcoin?

Yes. It performs SHA-256 hashing used for Bitcoin mining and supports compatible pool and solo-pool endpoints.

Can I solo mine with the Thor P2?

Yes, through a compatible solo-pool or supported solo configuration. Finding a block is probabilistic, the odds are extremely long, and no block or return is guaranteed.

What comes in the Thor P2 box?

The package includes the assembled and tested miner, ABS stand, 240W power adapter, US AC cable, and EU AC cable.

Can I change the fan lighting?

Yes. The ARGB fan supports color cycle, marquee, breathing, and flashing effects, and the lighting can be turned off.

Is Bitcoin mining with the Thor P2 profitable?

Profitability changes with Bitcoin price, network difficulty, block rewards, pool fees, uptime, selected mode, and electricity cost. CryptoCloaks does not promise a fixed return or block result.

The post Hammer Miner Thor P2 | 10 TH/s Home Bitcoin Miner appeared first on CryptoCloaks.